Beer Tower Cooler

Produktbeschreibung

Beer Tower Cooler Fan

Installing Your Beer Tower Cooler Fan

Installation Instructions:

Push the open end of your cooler hose into your beer tower until it bumps into your beer shanks and stops. Zip-tie your beer tower cooler air hose to your beer line with the included zip-tie so it can’t fall out later. Locate the fan end so that it’s not touching anything inside your kegerator and will not make any excessive noise when it’s running. Plug the power supply into a wall outlet or extension cord and run the thin power cable past the kegerator door gasket and plug into the Beer Tower Cooler. If you hear the fan running with your kegerator door closed, make sure the fan end has not moved to where it’s touching something inside your kegerator, and reposition if needed. For a cleaner looking install, run the power cord through a small hole drilled through the side or back of your kegerator. Be careful to avoid refrigerant lines if you decide to drill through the side or back of your kegerator. If you aren’t sure, don’t drill!!!! What our Beer Tower Cooler Fan Solves

The beer tower on a direct draw min-fridge style kegerator gets warm because warm air naturally rises and cold air falls down into the fridge.

And what’s right in the top of your beer tower? Your beer faucet and beer shank that the faucet attaches to. Our beer tower cooler fan blows a small amount of cold air onto your beer shank, keeping it cold and reducing foam.

Merkmale
Keeps your beer shank cold to help prevent foaming beer
Draws less power than an old school 15 Watt night light
Designed to run 24X7
Easy to install
Low cost
Blows air through a smooth 1/2″ X 3/4″ hose

Merkmale

Our beer tower coolers are designed to blow a small amount of cold air through the hose and onto your beer shanks. This air-flow keeps your beer shank cold to help reduce beer foam when you draw a glass of beer. Our beer tower cooler was designed to run continuously and it draws less power than an old style 15 Watt night light. Unplugging your beer tower cooler when not in use will degrade its performance because your beer shanks will warm up to room temperature between sessions.

Our beer tower cooler was manufactured with the best components possible, while keeping the cost low enough to keep it affordable to just about anyone. Our goal was to manufacture a product that would pay for itself within 1 oder 2 kegs of beer, and I believe we succeeded. But just like any other low-cost component, there are bound to be failures. Please feel free to request a free replacement if you experience a failure at any time within one year of your original purchase.

in den Warenkorb legen
in den Warenkorb legen
in den Warenkorb legen
in den Warenkorb legen
in den Warenkorb legen
in den Warenkorb legen

Kundenbewertungen

3.3 aus 5 Sterne 27
3.8 aus 5 Sterne 42
2.8 aus 5 Sterne 6
3.6 aus 5 Sterne 7

Preis
$29.99
$29.99
$29.99
$34.99
$34.99
$34.99

Geschwindigkeit
Standard
Standard
Standard
High
High
High

+5 Faucet Protectors
No
Ja
No
No
Ja
No

+5 Faucet Brushes
No
No
Ja
No
No
Ja

Works with any 2.5″, 3″, 4″ or T style „open center“ beer tower – Odds are, your beer tower is one of these. Blows cold air into your beer tower to keep your beer ice cold and help reduce beer foam. Includes a one year unconditional warranty. If your Beer Tower Cooler fails, just contact us through your Amazon order and we will replace it for free! Does not include a power switch. Our beer tower cooler is designed to run all the time to keep your beer in your tower ice-cold! But it draws less power than an old school night light. Easy to install – just insert into your beer tower from inside your kegerator until the hose reaches the top, zip-tie the hose to your beer line with the included zip-tie so it does not slip out. 2.5” beer towers will require wiggling the hose to work the end up to the top of your tower. Will need an extension cord. No matter whose beer tower cooler you buy, you will need an extension cord for your cooler’s power supply. Completely pre-assembled – no assembly required.