High flow beer tower cooler with 5 beer faucet brushes

Descripción del Producto

Beer Tower Cooler Fan

Installing Your Beer Tower Cooler Fan

Installation Instructions:

Push the open end of your cooler hose into your beer tower until it bumps into your beer shanks and stops. Zip-tie your beer tower cooler air hose to your beer line with the included zip-tie so it can’t fall out later. Locate the fan end so that it’s not touching anything inside your kegerator and will not make any excessive noise when it’s running. Plug the power supply into a wall outlet or extension cord and run the thin power cable past the kegerator door gasket and plug into the Beer Tower Cooler. If you hear the fan running with your kegerator door closed, make sure the fan end has not moved to where it’s touching something inside your kegerator, and reposition if needed. For a cleaner looking install, run the power cord through a small hole drilled through the side or back of your kegerator. Be careful to avoid refrigerant lines if you decide to drill through the side or back of your kegerator. If you aren’t sure, don’t drill!!!!

What our Beer Tower Cooler Fan Solves

The beer tower on a direct draw min-fridge style kegerator gets warm because warm air naturally rises and cold air falls down into the fridge.

And what’s right at the top of your beer tower? Your beer faucet and beer shank that the faucet attaches to. Our beer tower cooler fan blows a small amount of cold air onto your beer shank, keeping it cold and reducing foam.

Características

Keeps your beer shank cold to help prevent foaming beer
Draws less power than an old school 15 Watt night light
Designed to run 24X7
Fácil de instalar
Low cost
Blows air through a smooth 1/2″ X 3/4″ hose

Características

Our beer tower coolers are designed to blow a small amount of cold air through the hose and onto your beer shanks. This air-flow keeps your beer shank cold to help reduce beer foam when you draw a glass of beer. Our beer tower cooler was designed to run continuously, and it draws less power than an old style 15 Watt night light. Unplugging your beer tower cooler when not in use will degrade its performance because your beer shanks will warm up to room temperature between sessions.

Our beer tower cooler was manufactured with the best components possible, while keeping the cost low enough to keep one affordable to just about anyone. Our goal was to manufacture a product that would pay for itself within 1 o 2 kegs of beer and I believe we succeeded. But just like any other low cost component, there are bound to be failures. Please feel free to request a free replacement if you have a failure any time within one year of your original purchase.

añadir a la cesta
Opiniones de los usuarios

3.3 fuera de 5 estrellas 27
3.8 fuera de 5 estrellas 42
2.8 fuera de 5 estrellas 6
3.6 fuera de 5 estrellas 7

Precio

$29.99
$29.99
$29.99
$34.99
$34.99
$34.99

Velocidad

Estándar
Estándar
Estándar
High
High
High

+5 Faucet Protectors

No
Sí
No
No
Sí
No

+5 Faucet Brushes

No
No
Sí
No
No
Sí

Works with any 2.5″, 3″, 4″ or T style “open center” beer tower – Odds are, your beer tower is one of these. Blows cold air into your beer tower to keep your beer ice cold and help reduce beer foam.
Includes a one year unconditional warranty. If your Beer Tower Cooler fails, just contact us through your Amazon order and we will replace it for free!
Built with a ¾” ID X 1” OD clear PVC hose and a quality 50mm 9.9 CFM blower motor for more airflow. Powered by an energy-efficient 1 Amp plug-in power supply.
Does not include a power switch. Our beer tower cooler is designed to run all the time to keep your beer in your tower ice cold! But it draws less power than an old school night light.
Fácil de instalar – just insert into your beer tower from inside your kegerator until the hose reaches the top, zip-tie the hose to your beer line with the included zip-tie so it does not slip out. 2.5” beer towers will require wiggling the hose to work the end up to the top of your tower.
Will need an extension cord. No matter whose beer tower cooler you buy, you will need an extension cord for your cooler’s power supply.
Completely pre-assembled – no assembly required.